PCBA Online Separator Vacuum Cleaner
2021-07-23
A large amount of blanks will be generated when the splitter is cutting. For PCB board this problem, manufacturers generally have complete vacuum cleaners, but we also need good vacuum cleaner characteristics, and shared vacuum cleaner maintenance, milling tool splitter and daily failure maintenance. Introduction of the vacuum cleaner of the brand of milling cutter splitting machine: The vacuum cleaner is used in an environment with a very high safety factor, and its noise is decibels. Suitable for quiet environment. Work on the work board is competent for cleaner work, and can restore functions. Usually, it is widely used in various industries or fields, such as electronic products and vacuum cleaning after PCB cutting. Features of the vacuum cleaner of the brand of milling cutter splitter: 1. Low noise, long battery life, high battery life: the dust collector of the splitter vacuum cleaner works automatically, and improves the battery life time of the fan, so that the machine can work continuously for a long time, and can run continuously for 7 x 24 hours . 2. High filtration efficiency: The best filter flow rate enables the machine to ensure the best air flow rate, and the manual filter vibrator makes the filter very easy to clean. 3. The garbage filter self-cleaning system, the high efficiency device and the bag processing system are optional equipment. 4. Simple operation and maintenance: super large-capacity trash can, with a quick and simple trash dumping system, which makes it easy to empty the trash. The structure design is stable and stable. 5. High filtration efficiency: The large filter of the filter, the best filter bag that can filter and filter garbage is optional. 6. Round design design: the theme coordinates are balanced, very beautiful and fashionable. 7. A stainless steel muffler is installed at the exit of the motor, so your working environment is quieter. The machine can work continuously and filter the air at the outlet. 8. The built-in cyclone divider machine manually vibrates and vibrates, and the rocker rocker is freely powered by shaking left and right, and it can be cleaned at any time when it is started. 9. The independent dust collecting bucket can be cleaned easily, avoiding secondary pollution to the environment. Maintenance method of vacuum cleaner of milling cutter dividing machine First, we will introduce the preparatory work before using the vacuum cleaner of the splitter. 1. Check the power cord, plug, switch and other damages of the vacuum cleaner, otherwise it needs to be damaged or replaced. 2. Check whether the dust suction bucket of the vacuum cleaner is cleaned, and whether the accessories (suction tube, pickpocket, dust bag, etc.) are blocked. 3. Check the suction status of the entire vacuum cleaner to confirm whether it is normal. Otherwise, be sure to check the connection position of the connection label and the sealing ring at the base of the nose. 4. Check and confirm the tasks of the working environment. If cleaning is collected, the dust bag should be filled. 2. Precautions for the use of the vacuum cleaner of the milling cutter splitter: 1. Whether the motor plug of the vacuum cleaner can be inserted, the motor will rotate after being charged, resulting in insufficient suction power and affecting the service life of the motor. 2. When the vacuum cleaner is cleaning, it can flexibly control the breeding, such as the farm. If only one or two motors can reach the goal, there is no need to start another motor. If a large area is cleaned, three basic ground cycles must be used. 3. In the process of using vacuum suction, the power connection should not be too long, the power cord cannot be lengthened when scattered, and the wire diameter should not be smaller than the machine. The voltage is biased for use by the machine. 4. Pay attention to the noise change of the vacuum cleaner motor. Noise, that is, there is a problem with the vacuum cleaner motor, which needs to be repaired in time. 5. When you need to pack your luggage, you should remove the nose of the machine, and the machine cannot be turned upside down to ensure that you will not enter life, and avoid risking to enter yourself, so as to avoid damage. Common maintenance problems and methods of vacuum cleaners for milling cutter splitting machines brand splitting machines: The vacuum cleaner of the splitter is a commonly used cleaning tool on the splitter. It has its own related facilities. It can be used to collect waste products, filter and clean air in the production of plate making machines, and can also be used with auxiliary cleaning facilities. Other auxiliary equipment can be generated during the production process and connected to the filter debris, which can protect the health of the cleaning agent to a certain extent. Due to the environment of the splitter vacuum cleaner, some minor problems usually occur in the splitter vacuum cleaner. No need to find professional maintenance personnel for maintenance. 1. The working principle of the vacuum cleaner. Sometimes, the opportunity for vacuuming is powerful and clean. The problem is simple. The dust bag is full, and the hole fee in the bag is blocked, so no garbage can enter. Cotton, the vacuum cleaner of the splitter should be removed, or the internal collector should be replaced. Dust bag, or remove the dust in the dust collector. 2. The filter bag is clogged Since the filter bag is easily involved, it is necessary to shake the dust collector frequently and remove it from the flannel. 3. The main problem of the vacuum cleaner of the vacuum cleaner and the vacuum cleaner of the splitter is the main problem of the vacuum cleaner of the milling cutter. First check whether the fan of the vacuum cleaner on the extension board is loose. If it is loose, tighten the fan. You can also add attention between the fans to facilitate if it is more stable. The seal between the top cover and the middle shell should be tightened by rotating. When loosening is found, the parts should be replaced and tightened in time. 4. The brush is loose or damaged. The mechanical and electrical brushes of the splitter of the milling machine are damaged, and consumers will continue, but the suction plate of the splitter vacuum cleaner will be weakened. At this time, the rotating brush should be speeded up, and the position of the brush and the unit should be adjusted by rotating. If the smart bristles do this, the effect on the Internet will be very good. Or replace with a new brush.
