PCBA in-line depaneling machine vacuum cleaner
2021-08-28
PCB generate a lot of dust when cut by a depaneling machine. In view of this problem, manufacturers generally have a complete set of vacuum cleaners, but we also need to know what the characteristics of a good vacuum cleaner is, and share the maintenance of the vacuum cleaner for milling cutter splitter and daily failure of maintenance.
Milling cutter parter brand parter vacuum cleaner introduces.
The parting machine vacuum cleaner is used in the environment with very high safety factor and its noise decibel is very low. Suitable for quiet environment. Work reliability is very high, can be competent for heavier cleaning work, and also has explosion-proof function.
Usually, it is widely used in various industries or fields for cleaning table tops, such as vacuum vacuuming after electronic products and PCB cutting.
The features of the milling knife depaneling machine brand depaneling machine vacuum cleaner.
1. Low noise, durable and high efficiency: the brush dust collector of the depanelizer vacuum cleaner allows the fan to withstand higher working temperature and improves the reliability and service life of the fan, so that the machine can work continuously for a long time and can run continuously for 7 x 24 hours.
2. High filtration efficiency: The larger filter area allows the machine to ensure optimal air flow, while the manual filter shaker makes the filter very easy to clean.
3. Modularity: filter self-cleaning system, high efficiency filter and bagged waste disposal system are optional equipment.
4. Easy to operate and maintain: Large capacity waste bin with quick and easy dumping system makes it very easy to empty the waste. Compact and stable structure design.
5. High filtration efficiency: The large surface area of the filter ensures optimal filtration when filtering dust. Effective filters and garbage bags are optional.
6. Compact and elegant design: The body is designed with symmetrical balance, which is very beautiful and fashionable.
7. Stainless steel muffler is installed at the outlet of the motor, so your working environment is quieter. The machine can work continuously and filter the discharged air.
8. Built-in cyclone separator and manual dust removal vibration, cleaning the cartridge only need to gently shake the handle lever left and right to clean the cartridge, the same can be cleaned in the power on state.
9. Independent dust collection barrel, easy and quick to clean, avoiding secondary pollution of the environment.
Maintenance method of the miter slitter vacuum cleaner
First of all, we will introduce the preparation work before using the slitter vacuum cleaner.
1. Check whether the power cord, plug, switch and other parts of the vacuum cleaner are damaged, otherwise they need to be repaired or replaced.
2. Check whether the vacuum cleaner's dust bin is cleaned and whether the accessories (suction pipe, dust picker, dust collection bag, etc.) are clogged.
3. Check the suction status of the whole vacuum cleaner to confirm if it is normal. Otherwise, you must check the connection position of the connecting parts and the seal at the nose root.
4. Check and confirm the cleaning task of the working environment. If dust is collected, the dust collection bag should be filled.
2. Precautions for the use of vacuum cleaner for milling and slitting machine.
1. Check whether the vacuum cleaner motor plug is inserted firmly and securely, otherwise the motor will fluctuate when charged, resulting in insufficient suction power and affecting the service life of the motor.
2. When vacuum cleaner cleaning, you can control the motor flexibly, such as the motor. If only one or two motors can reach the target, there is no need to start another motor. If a large area is cleaned, three motors must be used to cycle as much as possible.
3. During the use of the vacuum cleaner, the power connection should not be too long, the power cord should not be extended without authorization, and the wire diameter should be no smaller than the machine requirements. Also, the power cord should not be wound in a circle to produce a magnetic field, which will result in insufficient voltage for the machine.
4. Pay attention to the noise change of the vacuum cleaner motor. If the noise of the motor changes suddenly and drastically, it is necessary to check the connection tube, or whether the capacity is full. In this case, it is necessary to clean the pipes or objects in the barrel. There is also a huge noise that there is a problem with the vacuum cleaner motor, which needs to be repaired in time.
5. When it is necessary to clean the inhalation dust, the nose should be removed and the machine should not be placed upside down to ensure that dust does not enter the motor and to ensure that no corrosive objects enter the motor so as to avoid damage.
Milling sub-board machine brand sub-board machine vacuum cleaner common maintenance problems and methods.
The depaneling machine vacuum cleaner is a common cleaning tool used on depaneling machines. It has a set of associated support facilities. It can be used to collect scrap, filter and clean air during the production process of the plate making machine, or it can be used simultaneously with auxiliary cleaning facilities. In connection with other auxiliary cleaning facilities it is possible to filter dust and debris generated during the production process, thus protecting the health of the cleaner to a certain extent.
Due to the cleaning environment of the parting machine vacuum cleaner, there are usually some minor problems in the parting machine vacuum cleaner. Here we will teach you some common problems and maintenance methods of vacuum cleaners for partitioners so that you don't need to look for professional maintenance personnel for maintenance when the following problems occur
1, the vacuum cleaner is not working enough.
Sometimes, the vacuum will feel laborious and not clean enough. The problem is simple. The dust collection bag is full or the hole in the bag is blocked, so trash cannot enter. In this case, the vacuum with the diverter should be removed, or the internal dust collection bag should be replaced, or the dust should be removed from the dust collector. The hose should be cleaned.
2. Filter bag blockage
Since the filter bag is easy to stick to dust, the dust collection frame must be shaken frequently and dust must be shaken off from the lint.
3. The problem in the parts of vacuum cleaner and the parts of vacuum cleaner of depanelizer is the main problem of no vacuum in the vacuum cleaner of miter depanelizer.
First check if the fan of the vacuum cleaner of the depaneling machine is loose, if it is loose, tighten the fan. You can also add lubricant between the fans to make them rotate more smoothly. The seal between the top cover and the middle shell should be tightened by screws.
When loose is found, the gasket around the motor should be replaced frequently and tightened in time.
4. The dust brush is loose or damaged.
If the brush of milling cutter parting machine brand parting machine is damaged, the motor will still rotate, but the suction power of the parting vacuum will be weakened. At this time, the rotating brush should be disassembled again, and the position of the rotating brush and unit should be adjusted to make the bristles rub fully with the ground. This will result in good dust removal. Or replace the brush with a new one.
Translated with www.DeepL.com/Translator (free version)
